Probe chip nanofabrication enabled reverse tip sample scanning probe microscopy concept and measurements.

We introduce a new scanning probe microscopy (SPM) concept called reverse tip sample scanning probe microscopy (RTS SPM), where the tip and sample positions are reversed as compared to traditional SPM. The main benefit of RTS SPM over the standard SPM configuration is that it allows for simple and fast tip changes. This overcomes two major limitations of SPM which are slow data acquisition and a strong dependency of the data on the tip condition. A probe chip with thousands of sharp integrated tips is the basis of our concept. We have developed a nanofabrication protocol for Si based probe chips and their functionalization with metal and diamond coatings, evaluated our probe chips for various RTS SPM applications (multi-tip imaging, SPM tomography, and correlative SPM), and showed the high potential of the RTS SPM concept.

Chemical Vapor Deposition of a Single-Crystalline MoS2 Monolayer through Anisotropic 2D Crystal Growth on Stepped Sapphire Surface.

Recently, a step-flow growth mode has been proposed to break the inherent molybdenum disulfide (MoS2) crystal domain bimodality and yield a single-crystalline MoS2 monolayer on commonly employed sapphire substrates. This work reveals an alternative growth mechanism during the metal-organic chemical vapor deposition (MOCVD) of a single-crystalline MoS2 monolayer through anisotropic 2D crystal growth. During early growth stages, the epitaxial symmetry and commensurability of sapphire terraces rather than the sapphire step inclination ultimately govern the MoS2 crystal orientation. Strikingly, as the MoS2 crystals continue to grow laterally, the sapphire steps transform the MoS2 crystal geometry into diamond-shaped domains presumably by anisotropic diffusion of ad-species and facet development. Even though these MoS2 domains nucleate on sapphire with predominantly bimodal 0 and 60° azimuthal rotation, the individual domains reach lateral dimensions of up to 200 nm before merging seamlessly into a single-crystalline MoS2 monolayer upon coalescence. Plan-view transmission electron microscopy reveals the single-crystalline nature across 50 µm by 50 µm inspection areas. As a result, the median carrier mobility of MoS2 monolayers peaks at 25 cm2 V-1 s-1 with the highest value reaching 28 cm2 V-1 s-1. This work details synthesis-structure correlations and the possibilities to tune the structure and material properties through substrate topography toward various applications in nanoelectronics, catalysis, and nanotechnology. Moreover, shape modulation through anisotropic growth phenomena on stepped surfaces can provide opportunities for nanopatterning for a wide range of materials.

MXene-Decorated Nylon Mesh Filters for Improvement of Indoor Air Quality by PM2.5 Filtration.

Air pollution is a problem that is increasing day by day and poses a threat on a global scale. Particulate matter (PM) is one of the air pollutants that is the biggest concern regarding air quality. In order to control PM pollution, highly effective air filters are required. This is especially necessary for PM with a diameter of less than 2.5 micrometers (PM2.5), which poses a health risk to humans. In this study, we demonstrate for the first time the use of a two-dimensional titanium carbide (Ti3C2) MXene nanosheets-decorated nylon mesh (MDNM) as a low cost and highly efficient PM2.5 filter. This study develops a proof-of-concept method to capture PM2.5. Thanks to their high specific surface area and active surface-terminating groups, conductive MXene nanosheets have made nylon mesh filters promising candidates for air filtration. The developed filters used electrostatic force to capture PM2.5 and showed high removal efficiency (90.05%) when an ionizer was used and under an applied voltage of 10 V, while a commercial high-efficiency particulate air (HEPA) filter had a removal efficiency of 91.03% measured under identical conditions. The proposed filters, which stand out with their low energy consumption, low pressure drop (∼14 Pa), and cost-effectiveness, have the potential to be a strong competitor to conventional PM filter systems used in many fields.

Highly stable silver-platinum core-shell nanowires for H2O2 detection.

Silver nanowire (Ag NW) networks have great potential to replace commercial transparent conducting oxides due to their superior properties in conjunction with their competitive cost, availability and mechanical flexibility. However, there are still challenges to overcome for the large scale utilization of Ag NWs in devices due to oxidation/sulfidation of NWs, which leads to performance loss. Here, we develop a solution-based strategy to deposit a thin platinum (Pt) shell layer (15 nm) onto Ag NWs to improve their chemical, environmental and electrochemical stabilities. Environmental and thermal stabilities of the core-shell NW networks were monitored under different relative humidity conditions (RH of 43, 75 and 85%) and temperature settings (75 °C for 120 hours and 150 °C for 40 hours) and compared to those of bare Ag NWs. Afterwards, stability of core-shell NW networks in hydrogen peroxide was investigated and compared to that of bare Ag NW networks. The potential window for electrochemical stability of the Ag NW networks was broadened to 0-1 V (vs. Ag/AgCl) upon Pt deposition, while bare Ag NWs were stable only in the 0-0.6 V range. Moreover, Ag-Pt core-shell NWs were used for the detection of hydrogen peroxide, where a high sensitivity of 0.04 µA µM-1 over a wide linear range of concentrations (16.6-990.1 µM) with a low detection limit (10.95 µM) was obtained for the fabricated sensors. All in all, this highly effective and simple strategy to improve the stability of Ag NWs will certainly open new avenues for their large-scale utilization in various electrochemical and sensing devices.

All-Solution-Processed, Oxidation-Resistant Copper Nanowire Networks for Optoelectronic Applications with Year-Long Stability.

Copper nanowires (Cu NWs) hold promise as they possess equivalent intrinsic electrical conductivity and optical transparency to silver nanowires (Ag NWs) and cost substantially less. However, poor resistance to oxidation is the historical challenge that has prevented the large-scale industrial utilization of Cu NWs. Here, we use benzotriazole (BTA), an organic corrosion inhibitor, to passivate Cu NW networks. The stability of BTA-passivated networks under various environmental conditions was monitored and compared to that of bare Cu NW control samples. BTA passivation greatly enhanced the stability of networks without deteriorating their optoelectronic performance. Moreover, to demonstrate their potential, BTA-passivated networks were successfully utilized in the fabrication of a flexible capacitive tactile sensor. This passivation strategy has a strong potential to pave the way for large-scale utilization of Cu NW networks in optoelectronic devices.